Paper receiving function
1. Flat paper dryer, dryer, powder spraying device
Some functions of receiving paper are edited under (Paper Stroke) menu, and some are edited under (Paper Stroke / Receiving Paper) menu.
Selection of functions under the delivery schedule menu:
a. Select the paper travel button under the menu bar (Figure 7-50 / â‘ ) to open the paper travel menu.
b. Use the suction button (Figure 7-50 / â‘£) to turn on or off the suction on the flat sheet.
c. Use the dryer button (Figure 7-50 / â‘¢) to turn on or off the infrared dryer.
(Figure 7-50 Delivery schedule menu)
d. Use the powder sprayer button (Figure 7-50 / â‘¡) to turn the powder sprayer on or off.
If a function is turned on, its corresponding label (Figure 7-50 / ⑤) will appear below the outline of the printing press.
2. Paper stroke-take-up
(Paper delivery) menu functions:
a. Use the paper guide suction button (Figure 7-51 / â‘ ) to turn on or off the suction on the take-up paper.
Under this menu, the operator can also adjust: the amount of powder sprayed, the speed of the suction roller / paper suction belt of the paper brake.
b. Use the +/- button (Figure 7-51 / â‘¡) to set the speed of the suction roller / paper belt (paper brake). Its value is represented by a bar graph 7-51, and it is marked on the top of the graph in digital form (off = 0%).
(Figure 7-51 Function of the delivery menu)
c. Use the +/- button (Figure 7-51 / â‘¢) to set the amount of powder sprayed. Its value is represented by a bar graph, and it is marked above the graph in digital form. [next]
3. Direct operation control of the delivery function
Open the blower unit and suction function on the suction drum when the offset press is not in production:
· Suction: Press the paper guide suction button (Figure 7-52 / ①).
· Suction roller: press the blow button of the suction roller (Figure 7-52 / ②).
(Figure 7-52 Direct operation control of the delivery function)
16. Reduce the speed of the picker and the height of the stack
1. Deceler slow down
The CP2000 console can control the switch of the picker. The paper on the picker slips easily, so it is recommended that the paper placed on the picker be as small as possible.
a. Press the paper feed button on the menu bar (Figure 7-53 / â‘ ) to open the paper feed menu, and then press the paper stack button (Figure 7-53 / â‘¡) to open the paper stack button (Figure 7- 53).
b. Use the +/- button (Fig. 7-53 / â‘¢) to set the number of revolutions of the offset press inserted between the paper pick and paper pick.
Only when the paper stack passes through the electric eye, the paper picker can be inserted into the paper stack. From the start of this non-stop operation to the insertion time of the picker, the number of revolutions of the roller can be set by the console.
(Figure 7-53 Reduce the height of the stack)
The shortest dead time is 1 revolution and the longest dead time is 9 revolutions. The standard setting is 1 revolution. If the stagnation time is too long, the paper can easily slip off under the front edge of the paper stopper (the main stack will continue to fall).
2. Preset to reduce the stack height
It is preset to reduce the height of the paper stack for the first time, mainly to insert it into the paper table for paper insertion. This value can be set between 10mm and 300mm. If the input value of this value is less than 10mm, the delivery eye will set the lowering height by itself (Figure 7-54 / ①). The lowered mark will be displayed on the pile symbol (Figure 7-53 / ⑤). The main paper stack will automatically lower to the height of the electric eye.
a. Press the paper feed button on the menu bar (Figure 7-53 / â‘ ) to open the paper feed menu, and then press the paper stack button (Figure 7-53 / â‘¡) to open the paper stack menu.
(Picture 7-54 Receiving electric eye)
b. Use the +/- button (Figure 7-53 / â‘¥) to set the value for lowering the height.
Tip: The height of the electric eye is adjustable.
Lower the height for the second time after the paper table is completely inserted. This height can be set by the CP2000 console, and the value range is 0 ～ 300mm.
c. Use the +/- button (Figure 7-53 / â‘£) to set the value for lowering height 2
ABLE Fire Stone Sets, made of light ceramic raw materials or cement materials, light weight but strong not easy to break, hand-painted, natural colors and amazing details & realistic shapes, easy turn redness in the fire, can enhance the fireplace flame, all made of inorganic materials, odorless, fire-resistant temperature >900℃, product can be used for a long time, with reasonable price.
ABLE also have advanced molding technology for ceramic log called cast log, it is lighter, stronger, fuller details, and glowing area is larger in the fire.ABLE can supply many kind of log accessories for fireplace, such as pebbles, coals, charcoals, pine cones, maple leaves, aglow ember, top-grade rock wool, stained vermiculite, small coal chips, barks, balls and hollow ball, ceramic pitted pebble and rough Lava rock that won't burst in outdoor fire pit, Pumpkin lamp, Skull and bone for Halloween Decor fire, fireplace log grate etc.
ABLE factory is located in Yixing City, Jiangsu. It is a well-known production base for fire resistant insulation materials and environmental protection products. Yixing is also a city has developed commerce and convenient transportation. Our company sincerely hopes to cooperate with professional customers, and welcome to visit our factory!
Ceramic Fire Stones,Fire Stones For Firepit,Fire Pit Stones,Firepit Stones
Yixing Able Ceramic Fibre Products Co., Ltd , https://www.ablegaslogs.com