Not long ago, the General Administration of Press and Publication published the Product Quality Supervision and Inspection Center of the 20th National Book Fair, which had 2,434 specimens. Including the special collection and the exhibition extract two parts. Through expert testing, 18 kinds of books were found to exist, and serious quality defects were reported, accounting for 0.74% of all tested books. That is to say, the qualified rate for the printing of the exhibited books at the Expo was 99.26%. It is worth noting that the print quality defects accounted for 11.11% of the total defects, and the binding quality defects were as high as 88.89%. Compared with the quality inspection results of the books of the 19th Session of the 2009 Fair, the defects of printing quality accounted for 30.77% of the total defects, and the defects of binding quality accounted for 69.23% of the total defects. Among them, the most common problem was the opening of plastics.
From this set of data, we can see the problem. Nearly 90% of the book's quality problems arise in the post-printing period, the binding process. Moreover, with the continuous improvement of printing technology and the continuous improvement of equipment, printing companies have improved their ability and consciousness to improve and ensure the quality of print management, but this also highlights the problems in the process of binding after printing. At the same time as the printing quality continues to increase, it has been ignored after printing. Obviously, the binding quality has dragged on the hind legs of printing quality. Why has the quality of printing been improved in a short period of one year, but India has been stalled or even withdrawn?
We all know that post-press binding has always been the most neglected link in the industry. This dates back to the beginning of the founding of the People's Republic of China. There was an unwritten rule in the printing factory in the early years. The revision of the work, the body is better assigned to the printing shop, open the printing press, the rest of the 'retrospection' will only be printed. It is the "tradition" left behind that year that has led to the most neglected post-press printing in the entire printing process. There are a large number of domestic companies engaged in the manufacture of printing machinery. However, the focus on printing equipment is rare, most companies have their eyes on prepress and printing.
The convening of this year's World Expo and the Fair has already sent us a signal that the future printing industry will gradually bid farewell to the development of the traditional simple printing model toward the fine print. The development of fine print is not only the substrate for prepress production, but also the most important and fundamental one for India and India. After the Indian expert Wang Huaizhu once said in an exclusive interview with HC360.com: “Post-press processing is often neglected in the entire process of publishing and printing. In fact, it is necessary to print fine books, and communication between pre-press design and post-press binding is very high. important!"
As the old saying goes, there are 90 and 90-odd people. After 90 miles of walking, it is only half the time. It is important to understand the last step. Whether it is prepress or printing, it is only based on the basics. If there is no good post-press binding, all previous work will be equal to zero.
From this set of data, we can see the problem. Nearly 90% of the book's quality problems arise in the post-printing period, the binding process. Moreover, with the continuous improvement of printing technology and the continuous improvement of equipment, printing companies have improved their ability and consciousness to improve and ensure the quality of print management, but this also highlights the problems in the process of binding after printing. At the same time as the printing quality continues to increase, it has been ignored after printing. Obviously, the binding quality has dragged on the hind legs of printing quality. Why has the quality of printing been improved in a short period of one year, but India has been stalled or even withdrawn?
We all know that post-press binding has always been the most neglected link in the industry. This dates back to the beginning of the founding of the People's Republic of China. There was an unwritten rule in the printing factory in the early years. The revision of the work, the body is better assigned to the printing shop, open the printing press, the rest of the 'retrospection' will only be printed. It is the "tradition" left behind that year that has led to the most neglected post-press printing in the entire printing process. There are a large number of domestic companies engaged in the manufacture of printing machinery. However, the focus on printing equipment is rare, most companies have their eyes on prepress and printing.
The convening of this year's World Expo and the Fair has already sent us a signal that the future printing industry will gradually bid farewell to the development of the traditional simple printing model toward the fine print. The development of fine print is not only the substrate for prepress production, but also the most important and fundamental one for India and India. After the Indian expert Wang Huaizhu once said in an exclusive interview with HC360.com: “Post-press processing is often neglected in the entire process of publishing and printing. In fact, it is necessary to print fine books, and communication between pre-press design and post-press binding is very high. important!"
As the old saying goes, there are 90 and 90-odd people. After 90 miles of walking, it is only half the time. It is important to understand the last step. Whether it is prepress or printing, it is only based on the basics. If there is no good post-press binding, all previous work will be equal to zero.
sofa booth for office, office sofa booth, hot sale soundproof sofa
Feat Top International(China) CO.,LTD , https://www.nbfeattop.com